![]() Compatible: This stick can be used with a wide range of phones including various Samsung, iPhones, and Google Pixel models.Using a Mpow selfie stick can give you a lot of flexibility in capturing photos. The stick can then be placed in your pocket and used later. Hold the shutter button for 3 seconds to shut the stick down. Then draw the telescopic stick back and rotate the clamp back to its original position. ![]() After UseĪfter you are done using the selfie stick, unscrew the clamp and take your phone out of it. Click the button again to stop recording. Hold the handle and press the shutter button to start the recording. ![]() For capturing videos, open your desired camera app and switch to the video mode.You can try various angles and shorten or increase the length of your stick. Press the shutter button to capture the photo.Open the camera app on your phone and then hold the handle so the phone gets stretched out by the stick.Step 6: Capture Photos and VideosĪfter attaching your phone it is time to capture photos. Make sure that any part of the stick is not touching your screen or there could be chances of damage to the screen.Make sure that your phone fits and then tighten the knob until it is secure.Unscrew the knob and place the phone in the foldable clamp. Hold the handle and stretch the telescopic stick out of its position.A good practice is to rotate it 270 degrees. Rotate the foldable clamp according to your preference.To attach your phone to the stick follow these steps: Your phone will also show connected and this will indicate that the stick has been connected successfully. The blue light on the stick will turn bright and stable. If you are connecting for the first time, search Mpow iSnap X and then tap on it to connect it. Go to settings and then connectivity and turn on Bluetooth. Make sure that your phone’s camera settings are set to being able to capture photos using the volume up (+) button.Īfter this, take your phone. The blue light on LED 1 will start blinking which means that the device is ready to be paired with your phone. Do remember that this stick is for phones and not cameras or GoPros.įirst, hold the shutter button (at the front) for 3 seconds and then release it. Therefore check if your phone is compatible with this stick, before trying to connect it. This stick is not compatible with Windows phones such as old Nokia devices, Blackberry or any other that does not have the capabilities mentioned above. These include older and newer versions of iPhones such as the iPhone 6s and the iPhone X. Besides Android, it can be used with any phone that can take pictures with its Volume up (+) button. However, you must know that the stick might not be compatible with the newer versions of these Android phones. This would include any android phone with a Bluetooth 3.0 capability and includes phones such as Samsung Galaxy devices, Samsung Note series, Moto, Droid, and Nexus. The Mpow stick is compatible with Android phones. After a full charge it can work for around 5 hours. The battery works for 300 cycles after which you have to replace it. The battery capacity is 50mAh and it takes 1 to 2 hours to fully charge this device. ![]() The red light means that it is successfully charging and when the light goes off, it means that your stick has been fully charged and is now ready for use. This could be a charging port or even your laptop.Īfter you have attached it for charging you must observe the lights. You can connect the stick to an outlet with the cable that came in the box. So, before using it for anything you should first charge it. Like many other electronic devices, your selfie stick needs to be charged before use too. For reference, LED 2 is at the bottom while LED 1 is at the front. ![]() When the red light goes off, it shows that the stick has been fully charged now. Like many similar electronic devices, this shows that the stick is currently charging. Lastly, the red light stays on and does not blick on LED 2. You can therefore use it for various functions such as capturing photos, making videos and in essence using it as a remote controller. This indicates that the device is connected successfully with your selfie stick. The second indication is the blue light stays on and does not blink on LED 1. When LED 1 blue light blinks, it indicates that your stick is in pairing mode and you can connect it to your phone or any other device through Bluetooth. There are two LEDS and they light up when the stick is performing various functions. Before you start using the Mpow stick, you should know what the different lights on it represent. ![]()
0 Comments
Leave a Reply. |